About Us About Us
News

Summary of Common Problems, Causes, and Solutions for Crusher Hammer Heads

2026-06-12 248

The following is a summary analysis of common problems and corresponding causes of crusher hammer heads, covering typical failure modes throughout the entire lifecycle of production, use, and maintenance:

image.png

1、 Fracture failure

brittle fracture

Insufficient material toughness (such as high chromium cast iron not properly tempered)

Low temperature brittleness (working environment temperature below the material's ductile brittle transition temperature)

Internal defects (shrinkage, accumulation of inclusions)

Reason:

Typical features: Smooth fracture surface, radial cracks, no obvious plastic deformation

fatigue fracture

Alternating load action (resonance between impact frequency and hammer natural frequency)

Surface microcrack propagation (unpolished stress concentration area)

Reason:

Typical features: Shell like patterns can be seen on the fracture surface, and the crack sources are mostly located at stress concentration points

2、 Abnormal wear and tear

Non-uniform wear

Local overload caused by rotor imbalance (single hammer head mass deviation>3%)

Uneven distribution of materials (skewed feed inlet or worn lining)

Reason:

Performance: The working surface of the hammer head shows a single-sided "crescent shaped" wear

Accelerated abrasive wear

Material hardness exceeds the standard (SiO ₂ content>15%)

Insufficient surface hardness (HRC

Reason:

Quantitative indicator: Under normal working conditions, the wear rate of high chromium cast iron hammerhead should be less than 0.8g/ton of material

3、 Structural failure

Bolt hole cracking

Uneven pre tightening force during installation (torque deviation>20%)

Failure to chamfer the hole wall leads to stress concentration

Reason:

Preventive measures: Use a hydraulic tensioner to ensure even force distribution on the bolt assembly

Hammer handle deformation

Insufficient flexural section modulus (design safety factor

Excessive material blockage (material size>80% of feed inlet width)

Reason:

4、 Surface damage

hot crack

The cooling rate during welding repair is too fast (step cooling was not performed)

Working temperature>400 ℃ leads to a decrease in the red hardness of the material

Reason:

Morphological features: The surface is cracked and the depth is usually less than 2mm

Corrosion pit

Cl ⁻ erosion in wet process operation (concentration>200ppm)

The wear-resistant layer forms galvanic corrosion with the substrate

Reason:

High risk environment: working conditions such as sea sand crushing and chemical waste treatment

5、 Collaboration failure

Loose shaft hole

Error in selecting tolerance fit (it is recommended to use H7/k6 transition fit)

The side clearance of the keyway exceeds the standard (maximum allowable clearance ≤ 0.05mm)

Reason:

Locking failure

Improper anti loosening measures (not using thread locking adhesive or disc spring washer)

The vibration frequency is close to the natural frequency of the fastener

Reason:

6、 Material performance degradation

Decreased hardness

Excessive tempering temperature (>550 ℃ leading to carbide coarsening)

Long term high-temperature work triggers organizational transformation

Reason:

Testing standard: The decrease in surface hardness during the service life should be less than 3HRC

Resilience degradation

475 ℃ brittleness (high chromium cast iron works in a sensitive temperature range for a long time)

Hydrogen embrittlement (infiltration of hydrogen atoms into grain boundaries in humid environments)

Reason:

Systematic improvement suggestions

Design optimization

Using finite element analysis to optimize stress distribution (maximum stress

Promote modular design (vulnerable parts can be replaced separately)

process control

Adding rare earth elements to refine grain size (grain size ≥ 6) during the casting process

Using laser cladding technology to repair local wear (bonding strength>400MPa)

Operations Management

Establish a statistical system for impact frequency (up to 500000 forced replacements)

Implement regular non-destructive testing (magnetic particle testing interval ≤ 200 working hours)

Attachment: Quick Diagnosis Form

By systematically analyzing the root causes of problems and implementing targeted improvements, the service life of the hammer head can be significantly improved (typical improvement cases show an average life increase of 70-150%). Suggest establishing a failure mode database based on specific operating conditions to achieve predictive maintenance.